Author Topic: Skillz MPI "2JZ Slayer!"  (Read 39328 times)

0 Members and 1 Guest are viewing this topic.

SQPerformance

  • Administrator
  • Tire Shredder
  • *****
  • Posts: 50
  • Ban Hammer of Thor
Skillz MPI "2JZ Slayer!"
« on: September 24, 2012, 10:36:28 PM »
Quote from: skillz
while every Starquest  around me is doing 2JZ swaps I am staying true to the G54B.

Car Info:

Mega Squirt modded by scott87star
MSD 6al2
10mm MAGNECOR spark plug wires
Magna Intake with 75mm throttle body
Borg Warner s363  T4 turbo .88A/R
Treadstone Exhaust manifold
3" Exhaust straight out the back with glass pack
Tial MVR wastegate
ID2000 injectors
dual Bosch 044 pumps
R154 tranny
Bills adapter housing and tranny mount
ACT extreme pressure plate with 6 Pad Rigid Race Disc
3" intercooler piping
D2 coilover suspension
Toyo proxes R888 225/50/R16 on front 255/50R16 on rear
 
Engine:
forged Wiseco pistons
Race prepped Connecting rods with ARP rod Bolts
Oil pan baffle
BS Eliminated
3SX performance light  weight crank pulley
ARP head stud
block O-Ring
felpro head gasket
Schneider 6610 Heavy duty valve spring
Schneider 292 cam
MOOKEEH ADJUSTABLE CAMGEAR
SS 1mm Oversized Valves
3:90 Rear end gears
polyurethane engine mounts
polyurethane diff mounts

goal is 500HP on E85. trying to making it in the 10s in the 1/4mile with less horsepower than the 2jz swap cars in my area. any advise with be greatly appreciated.








SQPerformance

  • Administrator
  • Tire Shredder
  • *****
  • Posts: 50
  • Ban Hammer of Thor
Re: Skillz MPI "2JZ Slayer!"
« Reply #1 on: September 24, 2012, 10:38:50 PM »
Quote from: non-intercooled flatty
Nice!

I guess the first thing i'd look at closely is the valve/valve seat area, you say the 1 mm oversize which are back cut nicely so you'll get more flow.  BUT, and its a big butt, make sure you've matched the new valve size to the seat or you won't see any improvement.  For stock sized seats I've had the 1 mm oversize cut back down to stock diameter so they fit right.  Without enlarging the port throat you're actually slowing the flow down.

Your A/R of 0.88, I take it that is the turbine?

Quote from: skillz
Yes the exhaust inlet is .88A/R

Quote from: funkyp
Id make sure I had a good tune in place, then put the SKILLZ to work!
Be ready to turn some rpm's with that setup.

SQPerformance

  • Administrator
  • Tire Shredder
  • *****
  • Posts: 50
  • Ban Hammer of Thor
Re: Skillz MPI "2JZ Slayer!"
« Reply #2 on: September 24, 2012, 10:41:56 PM »
Quote from: funkyp
Do yourself a favor and pickup a driveshaft loop.

Quote from: funkyp
Annnnnd I strongly recommend getting your hands on some actual drag tires. Those are okay for street use, but will only break axles at the track. Find some Non radial tires.

Quote from: skillz
How much horsepower realistically do i need to get into the 10's?

Quote from: funkyp
depends on your gear and powerband. look at the 2jz guys and not even 700hp will get you there. You need practice for one. At a bare minimum in a light setup, 475-500rwhp

FunkyPhil

  • Administrator
  • Hero Member
  • *****
  • Posts: 1306
Re: Skillz MPI "2JZ Slayer!"
« Reply #3 on: November 26, 2012, 05:10:56 PM »
Dying to see where this setup goes!
87 Conquest Tsi: 519whp 519wtq 7.09@102--10.95@122
CLICK TO SEE BUILD

skillz

  • Tire Shredder
  • ***
  • Posts: 61
Re: Skillz MPI "2JZ Slayer!"
« Reply #4 on: November 29, 2012, 07:00:13 PM »
Update. there have been some changes to my setup. I am now using Gato performance intake manifold and exhaust manifold with T4 and 44mm wastegate. I also now using a single magnafuel 750 fuel pump. Scott at Elutions Design Bureau is re doing my wire harness for my megasquirt ECU . The Engine is back out the car do to getting the engine bay painted. I will post more pictures this weekend when i install the intake manifold and the exhaust.




skillz

  • Tire Shredder
  • ***
  • Posts: 61
Re: Skillz MPI "2JZ Slayer!"
« Reply #5 on: December 03, 2012, 08:23:46 PM »







FunkyPhil

  • Administrator
  • Hero Member
  • *****
  • Posts: 1306
Re: Skillz MPI "2JZ Slayer!"
« Reply #6 on: December 03, 2012, 09:53:46 PM »
looks nasty!

while its out, id upgrade that filter to 2x 10an or atleast a 12an out to a catch can.  ;)
The stock vent is for a 12a at 10psi.
87 Conquest Tsi: 519whp 519wtq 7.09@102--10.95@122
CLICK TO SEE BUILD

Vettekiller

  • OverBoost
  • **
  • Posts: 17
Re: Skillz MPI "2JZ Slayer!"
« Reply #7 on: December 23, 2012, 10:02:39 AM »
2jz slayer? That has yet to be seen. Get that thing done. We don't have all year.

notstock88

  • Sr. Member
  • *****
  • Posts: 171
Re: Skillz MPI "2JZ Slayer!"
« Reply #8 on: February 17, 2013, 12:15:22 PM »
where is the updates!?!

skillz

  • Tire Shredder
  • ***
  • Posts: 61
Re: Skillz MPI "2JZ Slayer!"
« Reply #9 on: March 20, 2013, 03:51:47 PM »
i have been working from state to state haven't time to put the car back together. sorry for the delay.

notstock88

  • Sr. Member
  • *****
  • Posts: 171
Re: Skillz MPI "2JZ Slayer!"
« Reply #10 on: April 23, 2013, 10:04:23 PM »
soooooo progress?

Vettekiller

  • OverBoost
  • **
  • Posts: 17
Re: Skillz MPI "2JZ Slayer!"
« Reply #11 on: July 23, 2013, 07:05:13 PM »
He went for a ride in a 2jz conquest. Probably going to jump tracks now!! Lol

skillz

  • Tire Shredder
  • ***
  • Posts: 61
Re: Skillz MPI "2JZ Slayer!"
« Reply #12 on: July 24, 2013, 05:51:17 AM »
The ride in the 2jz conquest was awesome, but i am staying G54B. if i do any 2jz swaps it will be in a 1990 BMW convertible 325I

FunkyPhil

  • Administrator
  • Hero Member
  • *****
  • Posts: 1306
Re: Skillz MPI "2JZ Slayer!"
« Reply #13 on: July 24, 2013, 08:43:48 PM »
Cool, lookin forward to updates. Didnt know there were any 2j quests left that ran....
87 Conquest Tsi: 519whp 519wtq 7.09@102--10.95@122
CLICK TO SEE BUILD

Sqr

  • TBI Guy
  • TBi WHP KING
  • Sr. Member
  • *
  • Posts: 347
Re: Skillz MPI "2JZ Slayer!"
« Reply #14 on: July 25, 2013, 03:16:50 AM »
Cool, lookin forward to updates. Didnt know there were any 2j quests left that ran....
Rumor has it they break a lot, and it's expensive.  :o